A Tank Tee is 1 4 inch compression fitting with several connections and accessory ports, when utilized the installation is neat and lightweight. The two main line connections, one for the inlet provide line from the water pump / well, one other connects to the release line to the plumbing system. 4 FPT item plug-ins for any stress switch, pressure gauge, relief device and drain device eliminate the necessity for having several fixtures and nipples which add mess around a pressure tank.

Varieties of Tank Tees

Tank tees can be purchased in various measures short (3”) to long (16”) to work with the connection sizes and locations on various brands of stress tanks. Both significant style kinds are Union and Non-union which may be known as strong or 1-piece tank tees. They are available in 1” and 1-¼” with female or male tank contacts. Irrespective tank tees are equipped for connecting to any pre-billed pressure tanks. Tank tee length dimensions are Middle-End-Measures (CEL)

Are utilized on stress tanks with the tank link protruding from the side of the tanks base. Short tees range from 3” to 4-1/2” CEL. Short tank tees can be purchased in several types of tank link as demonstrated below.

Long Tees Tank

Are utilized on pressure tanks using the tank link being either at the center or counteract within the base of the tanks base. Long tanks tees have men NPT tank link and can be purchased in several measures. Longer tank tees are required since the size from the stress tank selected raises, the CEL has to be adequate to extend the tee head out significantly sufficient so that the pressure change can threaded on or away without having contacting the pressure tank. Diagram, technology drawing

Union versus. Low-Union Tank Tees

Some great benefits of union tank tees are realized during preliminary set up, and considerably reduces the work included for tank substitute. A union type tee easily disconnects the previous tank, which can be eliminated in minutes leaving all of the line and accessory contacts and wiring undamaged. The new tank can then be installed using the tank tee lower leg from the aged tank, set in place and reconnected towards the tank tee head by tightening the union. Job done!

Union tees that incorporate an O-ring give a dependable watertight seal. No need to worry about the bond leaking. It is strongly recommended to pick a top quality tank tee that uses a North United states standard O-diamond ring which are readily available in case another one is ever needed.

Low-union tank tees do the exact same work, are less money and spend less on the purchase cost. Nevertheless, they simply do not possess the identical easy installation and time saving advantages especially when a tank must be changed. An added work included during set up or tank replacement will significantly surpass the primary cost savings in the tee.

Stainless Steel Tank Tees

Stainless-steel tank tees more cost competitive than No-Lead Bronze and are replacing bronze (red brass) tank tees because the creation of No-Lead specifications in 2014. Usually cast from 304 stainless which is incredibly durable and very corrosion resistant. Even though stainless tees can be more expensive than brass, they are doing not contain zinc relieving the difficulties with dezincification that can occur when utilizing brass alloy tank tees in intense water conditions. Another advantage is definitely the very high strength of stainless steel practically removes all chance of anxiety cracking when threading into female contacts.

Brass Alloy Tank Tees

Brass tank tees are less expensive and therefore are suited for installs generally in most areas. Nevertheless brass alloys2-07TK-25SF-2NL are certainly not as rust resistant as stainless, consequently installs in places that the water is highly corrosive to brass, it is suggested to upgrade to stainless.

Galvanized Tank Tees

Galvanized tees are less expensive than each stainless and brass tank tees. Their use is typically07HC125G limited to installations on galvanized pressure tanks with no kidney. Galvanized tees are selected to get rid of the risk of galvanic rust among dissimilar metals. Galvanized tank tees used in conjunction with galvanized nipple and fittings lgotli the issue. It is important to note that some plumbing codes do not allow the usage of galvanized fixtures and nipples, one should verify that galvanized tank tees meet all the relevant plumbing program code requirements.

Pvc material Tank Tees

Pvc material tank tees certainly are a very competitive option in comparison to stainless, brass, and07PT-25-2 galvanized materials. They are very resistant against rust, they may not be as long lasting as metal tank tees, nor are available numerous configurations readily available. They may become a really appropriate option, when proper PVC set up methods are followed, utilizing a higher-high quality line sealant mixture rather than PTFE line sealant adhesive tape and avoiding over tightening up will decrease the chance of more than stressing the feminine NPT item ports.

1/2″ Tee..